Cisco 350-001 Exam Certification – 100% Free VCE Files Flydumps

Exam A
What is the effect of using the “logging ari_server” command?
A. logs messages to the console named ari_server
B. logs messages to a syslog server named ari_server
C. logs messages to the buffer of the ari_server console
D. logs messages to a virtual terminal line called ari_server

Correct Answer: B
Which of the following provide for IBM mainframe attachment?

Correct Answer: C
If the DTE side of a serial link is in the condition below, which of the following actions may be taken to determine the problem?
Serial 0 is up, line protocol is down
A. Depending on local loopback test contact service provider
B. Replace local and remote hardware one component at a time
C. Reboot the serial cable
D. Check routers configuration
E. Perform a local loopback test

Correct Answer: E
Given the following configuration, which of the following are true as it pertains to a telnet session? (Choose all that apply)
Router2#sh run
Building configuration…

%SYS-5-CONFIG_I: Configured from console by console
Current configuration:
version 11.3
no service password-encryption
hostname Router2
interface Ethernet0
no ip address
interface Serial0
ip address
no ip mroute-cache
clockrate 56000
interface Serial1
no ip address

shutdown ! ip classless! line con 0 loginpassword ccieline 1 8 line aux 0 line vty 0 4no login! end
A. “ccie” will be used as the telnet password
B. No telnet login will be required
C. The “ccie” password will be used to enter the privilege EXEC mode from the telnet session
D. The “ccie” password will be used to enter the user EXEC mode
E. No telnet login will be allowed

Correct Answer: BC
What is the default queuing method of a Serial Interface on a Cisco Router, assuming a speed of less than T1?
A. Random Early Detection (RED)
B. Priority Queuing
C. Weighted Fair Queuing (WFQ)
D. Custom Queuing
E. First In First Out FIFO
F. Last In First Out (LIFO)

Correct Answer: C
Workstation A sends a frame to Workstation B. The devices shown are routers. Which of the following are true of the Layer 3 addresses at reference point A? (Choose all that apply.)
A. The source address will be that of Workstation A.
B. The destination address will be that of Workstation B.
C. The source address will be the outbound interface of Device 2.
D. The destination address will be the inbound interface of device.
Correct Answer: AB
Assuming a router with infinite processing power, how many seconds would it take to fill a serial
interface’s buffers if it: was connected to a T1 needed to transmit 250 packets per second each packet is 1500 bytes the maximum number of outgoing buffers is 100
A. 1 sec
B. .8 sec
C. 1.25 sec
D. .5 sec
E. 1.5 sec

Correct Answer: B
What is the major difference between the Ethernet version 2 frame and the 802.3 frame?
A. Ethernet uses a 802.2 header to describe type
B. 802.3 frame uses a two-byte Length field where Ethernet describes type
C. 802.3 frame uses a two-byte field for sequence numbers where Ethernet describes type
D. Ethernet uses a SNAP header
E. None of the above
F. There is no major difference

Correct Answer: B
Which of the following are problems associated with Link State routing protocols? (Choose all that apply.)
A. The count-to-infinity problem
B. The amount of memory and processing required
C. The bandwidth consumed by the initial link state flood
D. The size of routing table broadcasts
E. The longer time for convergence as compared to Distance Vector protocols

Correct Answer: BC
As a frame travels through a routed network the Mac address will always:
A. be rewritten as it moves through repeaters
B. the source address will remain the same but the destination address will change
C. the source address will change and the destination address will change
D. remain the same
E. change to reflect the current source and destination
Correct Answer: E